About Us Contact Us Order Status & Tracking Register & Log In My Cart
Computer Hardware PCs & Barebones Laptops Tablets Electronics Software Tools Deals
Browse Top Categories
Special Offers

Featured Products
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-12800) Dual Channel Kit Desktop Memory 997112, 9-9-9-24, 1.35V, w/ Ridgeback Heatsink
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-1280...
Only $79.99

vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad, iPhone and Other Mobile Devices
vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad...
Only $15.99

Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboard, Refurbished
Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboar...
Only $15.99

Home >> Resources | Support >> Installation Guides >> 

Assembly Instructions: Palo Alto PA-600 ATX and Micro-ATX Mid-Tower Case

Assembly Instructions: Palo Alto PA-600 ATX and Micro-ATX Mid-Tower Case

Contributed by William Gerristead

You are encouraged to make links to this article from your website and tell your friends

The following advice is based on many years of experience. They are provided as a free service to our customers and visitors. However, Directron.com is not responsible for any damage as a result of following any of these advice. You are welcome to distribute these tips free to your friends and associates as long as it's not for commercial purposes.

Congratulations on your purchase of the Palo Alto PA-600 computer case. The objective of this Tip Sheet is to make the assembly experience as straightforward and enjoyable as possible. Upon opening the shipping package, you may have noticed that this case differs in many ways from conventional stamped and folded sheet-metal cases, i.e. many more of its components are made of plastic and mounting hardware and accessories appear quite different. Due to the engineered nature of its design, assembly is almost completely tool-free. Unfortunately, the diagram that accompanies the motherboard is not easily grasped and the assembly sequence is not the most convenient, e.g., assembly STEPS A through D may be regarded as a dry-run, as it is easier to install the motherboard first and then install the drives.

Work Space
In the absence of an assembly workbench, it is best to have a stable, well-illuminated work-surface for motherboard and component mounting and final assembly. A card-table may prove most convenient, and its soft surface precludes the need to remove the right-panel to prevent scratching.

Figure 1. Case assembly components (drives not included). In the background are the case components. In the foreground in front of the disk drives are the floppy disk and CD-ROM drive mounting brackets (4) and the motherboard mounting bracket.

Assembly components, as shown above in Figure 1. Lay the case down on a clean surface on its right side. Open the case by removing the thumbscrew at the rear of the left-side panel. There are 2 latches on the back of this panel that may be lifted slightly from the back of the case while removing the side panel. The inside of the case appears below as Figure 2. The ATX I/O panel is shipped separately and should be clipped into place (as shown in STEP E on the diagram) before mounting the motherboard.

Figure 2. Inside of case, showing (CW from top-left) power supply, drive mounting cage, front-panel wiring harness, feet, and PCI/ISA slots. The I/O panel is the bright metal piece in the middle on the left side below the power supply.

Motherboard Mounting and Drive Installation
Attach the motherboard clamping bracket(s) as shown in STEP F. A photograph of this bracket installed on the motherboard appears as Figure 3. The motherboard is carefully placed into stakes that are already installed on the base-plate. At the same time, the rear-panel connectors should be guided through the corresponding holes on the I/O panel.

Installation of the motherboard-clamping bracket appears to the left. After this is attached, the motherboard may be placed on the baseplate and secured with the captive screw on the back-panel that threads into the clamp. Note that the screw should not be overtightened, as its torque specification is 6 kgf-cm.

After securing the motherboard, the front-panel connectors should be attached. Refer to the motherboard manual for the proper connections. Note that LEDs only work one way, and they will not light if reversed.

AGP/PCI and ISA cards may now be installed. Be very careful to avoid stressing the motherboard by applying too much force during card insertion. Each cards is secured to the chassis by a single screw.

After the drives are installed, they may be hooked up to the motherboard. Refer to the motherboard manual for the location and orientation of drive connectors.

After all components are mounted, the case may be closed. If the right-side panel was removed, it should be replaced first. Then the front-panel is installed, followed by the left-side panel, which is secured with a single thumbscrew. Avoid forcing the parts into place as they should all fit together quite smoothly.

| Go to Top | Directron.com Home |

Copyright © 2007, Directron.com. All Rights Reserved.

If you find this article useful, please create a link to it from your website or tell a friend about it. If you have any comments or suggestions about this article, please email information@directron.us

Customer Feedback through Yahoo!
Join our Newsletter

Shipping Policy Customer Service Payment Policy
  Tracking Orders
  Est. Shipping Cost
  Time-in-Transit Map
  FAQ - Shipping
  Top Reasons for Delays
  UPS, FedEx, Postal Office
  Walk-in Sales
  APO/FPO Orders
  Return Policy
  Account Applications
  Frequent Errors
  FAQ-Tech Support
  Order Status
  Credit Card via Phone
  Purchase Order
  Prepay, PayPal
  Resellers, VARs
  Educational Government
  Terms & Conditions
  Price & Tax
Directron.NET- Help Desk Directron.ORG - Resources Short Cuts
  Sales Support
  Tech Support
  Knowledge Base
  Customer Service
  Open Forums
  Advanced Search of Help Desk
  How to Choose?
  FAQs, Glossary
  How to Upgrade?
  Top Sellers
  New Products
  Quiet Computers
  Water Cooling
  Case Painting

Directron Facebook Directron Twitter Directron Google+ Directron RSS Feed Directron YouTube Directron Newsletter Sign Up

BBB Accredited Business with an A+ Rating

Copyright  1997-2016 Directron, Houston, Texas. Prime Systems

Visit Our NEW Site!
Logisys CS6802BK Micro ATX Tower HTPC and SOHO Case, 1x 5.25i...
Only $45.99

LTS CMHT1422W-28 TVI Camera, HD 1080P, Up to 65ft IR Distance...
Only $69.99

LTS CMHR6123DWA Platinum 2.1MP HD-TVI Bullet Camera, 1/3in CM...
Only $189.99

Enermax iVektor ATX Mid Tower Soft Coating Computer Case ECA3...
Only $36.99

ILY 7 Targets 24x DVD/CD Duplicator...
Only $299.99

Acer K242HQL BBMD 23.6in LED LCD Monitor UM.UX6AA.B05, 5ms, 1...
Only $125.99

AOC e2260Swda 21.5in Slim Design 16:9 LED LCD Monitor (Black)...
Only $119.99

Belkin F9K1106 Dual-Band Wireless Range Extender, 4 x LAN Por...
Only $14.99

SanDisk Z400s SD8SBAT-256G-1122 2.5in 256GB SATA III Internal...
Only $75.99

Logitech 2.4GHz Wireless Keyboard and Mouse Combo MK270, Eigh...
Only $23.99

*Free Economy Shipping* TDK 77000021822 Glow in the Dark SP80...
Only $4.99

*Free Ground Shipping* Refurbished: Dell BELL8-Pro81-REFA Ven...
Only $125.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E1T0B/AM ...
Only $379.99

*Free Economy Shipping* PNY P-FD64GCOMB-GE Compact Attache 64...
Only $18.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E250B/AM...
Only $99.99

TrendNet TE100-S5 5-Port 10/100Mbps Fast Ethernet Switch...
Only $9.99