About Us Contact Us Order Status & Tracking Register & Log In My Cart
Computer Hardware PCs & Barebones Laptops Tablets Electronics Software Tools Deals
Browse Top Categories
Special Offers

Featured Products
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-12800) Dual Channel Kit Desktop Memory 997112, 9-9-9-24, 1.35V, w/ Ridgeback Heatsink
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-1280...
Only $79.99

vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad, iPhone and Other Mobile Devices
vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad...
Only $15.99

Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboard, Refurbished
Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboar...
Only $15.99

Home >> Resources | Support >> Installation Guides >> 

Instruction Sheet for PIA Micro ATX Cube Case

Instruction Sheet for PIA Micro ATX Cube Case

Contributed by Christopher Neff

You are encouraged to make links to this article from your website and tell your friends

The following advice is based on many years of experience. They are provided as a free service to our customers and visitors. However, Directron.com is not responsible for any damage as a result of following any of these advice. You are welcome to distribute these tips free to your friends and associates as long as it's not for commercial purposes.

Opening the Case:

To open the case, remove the five screws that attach the outer shell to the frame (see Figure 1). After screws are removed, slide the shell slightly toward the back of the case and lift it upward. Be cautious of sharp edges inside the case and at the edges of the outer shell! At this time, also remove the PS Hinge Screw and swing the power supply aside so it is out of your way, as shown in Figure 2.

Figure 1 - Screw Locations Figure 2

Mounting a Motherboard in the Case:

It is easiest to install the motherboard before any drives or other peripherals have been installed in the case. There are several industry standard form factors for motherboards; this case can accept either a flexATX motherboard or a small MicroATX motherboard. The largest motherboard that will fit this case is 9.5" x 9.0". To correctly mount your motherboard into the case, do the following:
1. Orient the motherboard to the case so that the integrated connectors are facing the back of the case. Make note of the mounting holes on the motherboard, and which holes on the bottom of the case they line up with. Note also which slot covers will need to be removed if you wish to install expansion cards, such as a modem or video card.
2. Using a slotted (flat head) screwdriver, remove unnecessary slot covers as shown in Figure 3 (next page).
3. Set the motherboard aside and turn the case on its side. Be careful - the power supply will move on its hinges as you tilt the case!
4. From the bottom of the case, insert the white plastic spacers into the holes on the case. Insert spacers only in the holes noted in step 1.
5. Set the case upright, align the motherboard as before, and secure it in place by screwing it to the spacers. If you will be using expansion cards, it is easier to install them at this time than after drives are installed. You should also install the CPU, CPU cooling fan, and memory at this time, following the directions provided with them.

Figure 3 - Removing Slot Covers

Installing Drives into the Drive Bays:

The case has bays for two external 5.25" drives, one external 3.5" drive, and one internal 3.5" hard drive. You may wish to use drives with black faceplates. To install drives, do the following:
1. Being careful of sharp edges, push the bay covers out through the faceplate from the inside. If you are installing two 5.25" drives, you may need to remove the metal cover inside the second slot using a technique similar to that used to remove slot covers in Step 2 of the above section.
2. Slide your external drives into place from the outside, aligning their faceplates with the front of the case. Screw them securely into place from the inside, using screws on both sides of the drives.
3. The hard drive bay is at the top of the 3.5" external bay. Place the hard drive in the bay with cable side facing the inside of the case and secure it with screws.
4. After all drives and cards are installed, swing the power supply back into position and secure it with the PS Hinge screw.

Cable Attachments:

Attach the power supply cable to the motherboard. There are also two types of plugs for the drives installed in the drive bays. The smaller one is used for the floppy drive, and the larger is used for all other kinds of drives, including hard drives and CD-ROMs.

WARNING: The power supply may not function unless the motherboard and at least one drive is plugged in. Some power supplies are designed not to function without a minimum load.

There are several wires attached to the inside front of the case. These wires power indicator lights and switches; the end of each is labeled with its function. Connect them to the motherboard according to the directions provided in the motherboard manual. As a rule, Pin 1 is indicated by the colored wire in each connector. You should also connect data cables to the drives and motherboard at this time, following the directions provided with those components.

| Go to Top | Directron.com Home |

Copyright © 2007, Directron.com. All Rights Reserved.

If you find this article useful, please create a link to it from your website or tell a friend about it. If you have any comments or suggestions about this article, please email information@directron.us

Customer Feedback through Yahoo!
Join our Newsletter

Shipping Policy Customer Service Payment Policy
  Tracking Orders
  Est. Shipping Cost
  Time-in-Transit Map
  FAQ - Shipping
  Top Reasons for Delays
  UPS, FedEx, Postal Office
  Walk-in Sales
  APO/FPO Orders
  Return Policy
  Account Applications
  Frequent Errors
  FAQ-Tech Support
  Order Status
  Credit Card via Phone
  Purchase Order
  Prepay, PayPal
  Resellers, VARs
  Educational Government
  Terms & Conditions
  Price & Tax
Directron.NET- Help Desk Directron.ORG - Resources Short Cuts
  Sales Support
  Tech Support
  Knowledge Base
  Customer Service
  Open Forums
  Advanced Search of Help Desk
  How to Choose?
  FAQs, Glossary
  How to Upgrade?
  Top Sellers
  New Products
  Quiet Computers
  Water Cooling
  Case Painting

Directron Facebook Directron Twitter Directron Google+ Directron RSS Feed Directron YouTube Directron Newsletter Sign Up

BBB Accredited Business with an A+ Rating

Copyright  1997-2016 Directron, Houston, Texas. Prime Systems

Visit Our NEW Site!
Logisys CS6802BK Micro ATX Tower HTPC and SOHO Case, 1x 5.25i...
Only $45.99

LTS CMHT1422W-28 TVI Camera, HD 1080P, Up to 65ft IR Distance...
Only $69.99

LTS CMHR6123DWA Platinum 2.1MP HD-TVI Bullet Camera, 1/3in CM...
Only $189.99

Enermax iVektor ATX Mid Tower Soft Coating Computer Case ECA3...
Only $36.99

ILY 7 Targets 24x DVD/CD Duplicator...
Only $299.99

Acer K242HQL BBMD 23.6in LED LCD Monitor UM.UX6AA.B05, 5ms, 1...
Only $125.99

AOC e2260Swda 21.5in Slim Design 16:9 LED LCD Monitor (Black)...
Only $119.99

Belkin F9K1106 Dual-Band Wireless Range Extender, 4 x LAN Por...
Only $14.99

SanDisk Z400s SD8SBAT-256G-1122 2.5in 256GB SATA III Internal...
Only $75.99

Logitech 2.4GHz Wireless Keyboard and Mouse Combo MK270, Eigh...
Only $23.99

*Free Economy Shipping* TDK 77000021822 Glow in the Dark SP80...
Only $4.99

*Free Ground Shipping* Refurbished: Dell BELL8-Pro81-REFA Ven...
Only $125.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E1T0B/AM ...
Only $379.99

*Free Economy Shipping* PNY P-FD64GCOMB-GE Compact Attache 64...
Only $18.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E250B/AM...
Only $99.99

TrendNet TE100-S5 5-Port 10/100Mbps Fast Ethernet Switch...
Only $9.99