About Us Contact Us Order Status & Tracking Register & Log In My Cart
Computer Hardware PCs & Barebones Laptops Tablets Electronics Software Tools Deals
Browse Top Categories
Special Offers

Featured Products
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-12800) Dual Channel Kit Desktop Memory 997112, 9-9-9-24, 1.35V, w/ Ridgeback Heatsink
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-1280...
Only $79.99

vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad, iPhone and Other Mobile Devices
vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad...
Only $15.99

Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboard, Refurbished
Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboar...
Only $15.99

Home >> Resources | Support >> Installation Guides >> 

Assembling & Installation Tips for FK-603 Cases

Assembling & Installation Tips for FK-603 Cases

You are encouraged to make links to this article from your website and tell your friends

The following advice is based on many years of experience. They are provided as a free service to our customers and visitors. However, Directron.com is not responsible for any damage as a result of following any of these advice. You are welcome to distribute these tips free to your friends and associates as long as it's not for commercial purposes.

Opening the Case:
Remove the back bezel by pushing the two plastic tabs on the right side away from the center and lifting the bezel off. You may add four case screws to tighten the back bezel but the new case does not come with the screws mounted to allow screwless entry. Then push the side panels toward the back of the case to open. WARNING: The side panels might be hard to remove. Be careful not to break the plastic tabs on the side panels.

Attaching the Case Feet:
Align the tabs on the top of the foot with the holes in the bottom of the case. Insert the tabs and slide the foot towards the front of the case until it clicks into place. Both feet attach in the same manner.

Installing Drives into the Drive Bays:
To remove the drive cage, press the latch on the side of the cage and slide it backward until it is free from the case. There are two cages, which can be removed individually or together. The holes in the side of the cage should match up with the drive you are trying to install. Use the m3 thread screws to attach the drive to the cage. When mounting a floppy drive, make sure that the front of the drive will be flush with the front of the case once you have mounted the drive cage.

To mount the cage, press the latch and line the tabs on the top of the cage with the holes on the bottom of the cage above it. Insert the tabs, and press the cage forward until it stops against the wall of the case. Release the latch.

To mount a drive into one of the 5.25-inch bays, first reach inside the drive cage and push the 5.25-faceplate out from the front of the case. Then, slide the drive in from the front of the case until it is flush with the front bezel. Note that it is only necessary to attach screws to one side of the cage to secure the drive. Tension stubs on the other side of the cage will provide enough tension to keep the drive in place.

Attaching the Front 8x8cm Case Fan:
Remove the case fan holder (black) by lifting the tab on the side of the holder outward and then pushing the holder upwards. The fan holder has four "legs" anchored to the front plate of the case. Insert the case fan from the front of the holder. Have the label on the fan facing the front of the case to allow air blowing out of the case. Mount the fan holder back by aligning the four "legs" and then pushing it downward until you hear a "click." If you are having difficulty removing or mounting the case fan holder, remove the front bezel first. It will help you by allowing you "seeing" the actions.

Mounting a Motherboard into the Case:
The motherboard you will put into this case will comply with one of several industry standards that involve the location of mounting holes and integrated components, and the type of power supply used. This case has been designed to be compatible with the AT, ATX, and Micro ATX standards. The type of motherboard that will be used most commonly with this case is an ATX motherboard, so that example will be used. To correctly mount the motherboard into the case, do the following:
(1) Remove the fan duct by pulling back on the tab as shown, and then sliding the duct down until it releases from the case.
(2) Orient the motherboard to the case so that the integrated connectors are facing the back of the case. Make note of the mounting holes on the motherboard, and which holes on the case they line up with.
(3) Screw the brass spacers into the mounting holes on the case.
(4) Place the motherboard into the case, lining up the holes with the brass spacers. Use the 6-32 thread screws to attach the motherboard. Refer to your motherboard manual when attaching the CPU, memory, expansion cards, etc.

Using the Optional Faceplate:
To remove the original faceplate, reach into the opening and pull up and out on the faceplate until it releases. To attach the optional faceplate, line up the tabs on the top of the faceplate with the ones on the case, and then snap it into place.

Cable Attachments:
Attach the power supply cable. Note that the fan duct cable is also plugged in. Most motherboards have a plug for this fan. There are two types of plugs for the drives installed into the drive bays. The smaller one is used for the floppy drive. The larger one is used for all other types of drives (hard drive, CDROM, etc.). There are several wires attached to the front bezel that power speakers, indicator lights, and switches. The wire connectors are labeled, and have an indicator (called Pin 1) as to which way they should be plugged in. The motherboard will have pins that these wires plug into, and will also have Pin 1 indicated. Refer to your motherboard manual for a diagram of the pin arrangement and its location on the board.

WARNING: The ATX power supply may not operate unless a working motherboard, processor, memory, video card, and at least one drive are plugged in. Some power supplies are designed not to operate unless they have a minimum load on them. If your system does not power up, it may not suggest a defective power supply, but indicate a problem somewhere else.

NOTE: Coarse-thread screws are normally used for mounting hard drives. Fine-thread screws are normally used for floppy drives and CD-ROM drives. Some cases use fine and some use coarse-thread screws for motherboards. Be sure to use appropriate screws to ensure proper installation with minimum damage.

| Go to Top | Directron.com Home |

Copyright © 2007, Directron.com. All rights reserved.

If you find this article useful, please create a link to it from your website or tell a friend about it. If you have any comments or suggestions about this article, please email information@directron.us

Customer Feedback through Yahoo!
Join our Newsletter

Shipping Policy Customer Service Payment Policy
  Tracking Orders
  Est. Shipping Cost
  Time-in-Transit Map
  FAQ - Shipping
  Top Reasons for Delays
  UPS, FedEx, Postal Office
  Walk-in Sales
  APO/FPO Orders
  Return Policy
  Account Applications
  Frequent Errors
  FAQ-Tech Support
  Order Status
  Credit Card via Phone
  Purchase Order
  Prepay, PayPal
  Resellers, VARs
  Educational Government
  Terms & Conditions
  Price & Tax
Directron.NET- Help Desk Directron.ORG - Resources Short Cuts
  Sales Support
  Tech Support
  Knowledge Base
  Customer Service
  Open Forums
  Advanced Search of Help Desk
  How to Choose?
  FAQs, Glossary
  How to Upgrade?
  Top Sellers
  New Products
  Quiet Computers
  Water Cooling
  Case Painting

Directron Facebook Directron Twitter Directron Google+ Directron RSS Feed Directron YouTube Directron Newsletter Sign Up

BBB Accredited Business with an A+ Rating

Copyright  1997-2016 Directron, Houston, Texas. Prime Systems

Visit Our NEW Site!
Logisys CS6802BK Micro ATX Tower HTPC and SOHO Case, 1x 5.25i...
Only $45.99

LTS CMHT1422W-28 TVI Camera, HD 1080P, Up to 65ft IR Distance...
Only $69.99

LTS CMHR6123DWA Platinum 2.1MP HD-TVI Bullet Camera, 1/3in CM...
Only $189.99

Enermax iVektor ATX Mid Tower Soft Coating Computer Case ECA3...
Only $36.99

ILY 7 Targets 24x DVD/CD Duplicator...
Only $299.99

Acer K242HQL BBMD 23.6in LED LCD Monitor UM.UX6AA.B05, 5ms, 1...
Only $125.99

AOC e2260Swda 21.5in Slim Design 16:9 LED LCD Monitor (Black)...
Only $119.99

Belkin F9K1106 Dual-Band Wireless Range Extender, 4 x LAN Por...
Only $14.99

SanDisk Z400s SD8SBAT-256G-1122 2.5in 256GB SATA III Internal...
Only $75.99

Logitech 2.4GHz Wireless Keyboard and Mouse Combo MK270, Eigh...
Only $23.99

*Free Economy Shipping* TDK 77000021822 Glow in the Dark SP80...
Only $4.99

*Free Ground Shipping* Refurbished: Dell BELL8-Pro81-REFA Ven...
Only $125.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E1T0B/AM ...
Only $379.99

*Free Economy Shipping* PNY P-FD64GCOMB-GE Compact Attache 64...
Only $18.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E250B/AM...
Only $99.99

TrendNet TE100-S5 5-Port 10/100Mbps Fast Ethernet Switch...
Only $9.99