About Us Contact Us Order Status & Tracking Register & Log In My Cart
Computer Hardware PCs & Barebones Laptops Tablets Electronics Software Tools Deals
Browse Top Categories
Special Offers

Featured Products
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-12800) Dual Channel Kit Desktop Memory 997112, 9-9-9-24, 1.35V, w/ Ridgeback Heatsink
Mushkin Blackline 16GB (2x8GB) 240-Pin DDR3 1600MHz (PC3-1280...
Only $79.99

vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad, iPhone and Other Mobile Devices
vitalASC KB10KA-S Ultra Slim Bluetooth 3.0 Keyboard, for iPad...
Only $15.99

Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboard, Refurbished
Logitech 920-003402 Keyboard Case for iPad 2 Wireless Keyboar...
Only $15.99

Home >> Resources | Support >> Installation Guides >> 

Directron 301T3 Instruction Guide

Directron 301T3 Instruction Guide

Contributed by Jonathan Bergknoff

You are encouraged to make links to this article from your website and tell your friends

The following advice is based on many years of experience. They are provided as a free service to our customers and visitors. However, Directron.com is not responsible for any damage as a result of following any of these advice. You are welcome to distribute these tips free to your friends and associates as long as it's not for commercial purposes.

Take out the case from the cardboard box and put it down on a clean, sturdy surface. To open the case remove the sides by unscrewing the two thumb screws on either side panel while gripping the handle groove and sliding backwards and then pulling away from the case. The motherboard tray is attached in the back by four thumb screws which you should also remove so that the case will be completely open for you to work with it.

Before beginning putting the computer together, take out the small cardboard box contained in the case. This box has screws, face plates, and other important trinkets.

Power Supply:
A power supply is a necessary component but does not come with the case by default. If you ordered one to be installed with the case, you can skip to the next section.

Guide the power supply on the support rails at the top and rear of the case. It should fit up against the back of the case snugly. Make sure you don't inadvertently block any of the fans on the power supply; it must be oriented so there is a fan and power connector socket visible from the back of the case. Some power supplies also have a fan which should face down towards the bottom of the case.

Hold the power supply to the back of the case with one hand and use four thumbscrews from the small cardboard box (that came inside the case) to fasten it.

You should have taken the motherboard tray out of the case in the first step. If you haven't, refer to "Disassembly" before continuing with this section.

There are several brass motherboard mounts in the bag (they are approximately the size of screws). Take between six and ten of these and put them in the appropriate places on the tray. Screw the mounts in by hand but make sure they are in firmly. To get an idea of which mounts to use, you should try to put your motherboard over the tray and see which mounts line up with holes on the motherboard. Six mounts should be sufficient but feel free to add more; less mounts could be dangerous, so be careful.

Check to see if your motherboard fits the I/O plate included with the case (above the PCI slot openings in the back of the case). If it does, you can move on to the next step. Use a flathead screwdriver to push down the corners of the I/O plate and nudge it out (in this case, out is in towards the front of the case). Put the I/O plate that came with your motherboard in the place of the one you just removed by pushing each of its corners in. Each corner will snap into place to let you know when it is fastened.

If you haven't already, it's suggested that you install your processor, cooler and RAM (but not PCI devices) on the motherboard prior to doing this step: Guide the motherboard gently into the I/O plate and onto the brass mounts. The holes in the motherboard should line up with the mounts. Put a screw in each of the mounts. When you're done with this step, the motherboard should be secured on the tray. Slide the tray back into the case and re-fasten it with the four thumbscrews you took out earlier.

External Drives:
Use a Phillips head screwdriver to remove the eight screws holding the front bezel in place. It is suggested that you then remove all placeholder faceplates that came with the case. You can remove them by squeezing both sides and pulling outward. Note: You should refrain from installing hard drives until the next section.

Slide each drive into place using the guides on either side. Screw them in tightly with at least two screws per side per drive. When all drives are installed, replace placeholder faceplates where appropriate. Push the bezel back into place and tighten all eight screws to secure it.

Internal Drives:
Near the front of the case at the bottom, there are three thumbscrews holding a drive cage. Remove this cage and put your hard drives (up to five) in it. Use provided screws to fasten the drives and replace the cage.

Finishing Up:
Optional. If you wish to have pass-through ports (they are located on the front bezel), you can use the included Firewire and sound (output and microphone) pass through cables. Use the included PCI faceplate which has a hole in it to send the cables out the back and to the required devices.

Optional. If you wish to use the front USB ports, it is necessary to consult your motherboard's documentation to determine the orientation and position which the USB cables must be plugged in with.

From the bezel, there are several small plugs which must be connected to your motherboard. These connections are motherboard-specific so you will again need to consult your manual. This step is not optional. These connectors enable the bezel power and reset buttons as well as power and hard drive lights.

Connect the big ATX power supply cable to your motherboard (this is a large bundle of wires which connects to your motherboard in one big plug). Connect any fans (on your CPU, from your BIOS, from your video card, etc.; not including case fans) to the motherboard fan connectors. Connect all drives and case fans to the power supply and to IDE cables as necessary.

Add any PCI/AGP devices, such as sound cards, network interface cards, and video cards, to the motherboard. Use included thumbscrews to fasten them. Hold onto the blank placeholder plates that you take out in case you need to re-use them in the future.

Put the sides of the case back on and refasten them with the thumbscrews you took off earlier. Connect the power supply to an outlet and hook up any other peripherals that you require.

Congratulations, assembly is complete on your Directron 301T3.

| Go to Top | Directron.com Home |

Copyright © 2007, Directron.com. All Rights Reserved.

If you find this article useful, please create a link to it from your website or tell a friend about it. If you have any comments or suggestions about this article, please email information@directron.us

Customer Feedback through Yahoo!
Join our Newsletter

Shipping Policy Customer Service Payment Policy
  Tracking Orders
  Est. Shipping Cost
  Time-in-Transit Map
  FAQ - Shipping
  Top Reasons for Delays
  UPS, FedEx, Postal Office
  Walk-in Sales
  APO/FPO Orders
  Return Policy
  Account Applications
  Frequent Errors
  FAQ-Tech Support
  Order Status
  Credit Card via Phone
  Purchase Order
  Prepay, PayPal
  Resellers, VARs
  Educational Government
  Terms & Conditions
  Price & Tax
Directron.NET- Help Desk Directron.ORG - Resources Short Cuts
  Sales Support
  Tech Support
  Knowledge Base
  Customer Service
  Open Forums
  Advanced Search of Help Desk
  How to Choose?
  FAQs, Glossary
  How to Upgrade?
  Top Sellers
  New Products
  Quiet Computers
  Water Cooling
  Case Painting

Directron Facebook Directron Twitter Directron Google+ Directron RSS Feed Directron YouTube Directron Newsletter Sign Up

BBB Accredited Business with an A+ Rating

Copyright  1997-2016 Directron, Houston, Texas. Prime Systems

Visit Our NEW Site!
Logisys CS6802BK Micro ATX Tower HTPC and SOHO Case, 1x 5.25i...
Only $45.99

LTS CMHT1422W-28 TVI Camera, HD 1080P, Up to 65ft IR Distance...
Only $69.99

LTS CMHR6123DWA Platinum 2.1MP HD-TVI Bullet Camera, 1/3in CM...
Only $189.99

Enermax iVektor ATX Mid Tower Soft Coating Computer Case ECA3...
Only $36.99

ILY 7 Targets 24x DVD/CD Duplicator...
Only $299.99

Acer K242HQL BBMD 23.6in LED LCD Monitor UM.UX6AA.B05, 5ms, 1...
Only $125.99

AOC e2260Swda 21.5in Slim Design 16:9 LED LCD Monitor (Black)...
Only $119.99

Belkin F9K1106 Dual-Band Wireless Range Extender, 4 x LAN Por...
Only $14.99

SanDisk Z400s SD8SBAT-256G-1122 2.5in 256GB SATA III Internal...
Only $75.99

Logitech 2.4GHz Wireless Keyboard and Mouse Combo MK270, Eigh...
Only $23.99

*Free Economy Shipping* TDK 77000021822 Glow in the Dark SP80...
Only $4.99

*Free Ground Shipping* Refurbished: Dell BELL8-Pro81-REFA Ven...
Only $125.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E1T0B/AM ...
Only $379.99

*Free Economy Shipping* PNY P-FD64GCOMB-GE Compact Attache 64...
Only $18.99

*Free Economy Shipping* Samsung 850 EVO-Series MZ-75E250B/AM...
Only $99.99

TrendNet TE100-S5 5-Port 10/100Mbps Fast Ethernet Switch...
Only $9.99